DIY Upper and Lower Cabinet Lighting Tutorial | Thrifty Decor Chick

How to install upper and lower cabinet lighting without an electrician.

There are a few ways to add your own lighting above and below your kitchen cabinets, and I’m sharing two of the easiest options here. 

This DIY project adds so much warmth and interest to a kitchen, but it also functions well because it creates great task lighting at night:

The lights and rope lights I shared years ago have a warmer glow, but it’s a lot harder to find those specific incandescent strips now. Also, they do burn out eventually and are bulkier. 

I much prefer the LED light strips now, and that’s what I’ve used for the past few years. That tutorial is still helpful no matter which option you choose!

We have an outlet behind the fridge that I was able to access. 

I cut a hole into the side of the cabinet and then ran the cord for the lighting through that:

I’ll go into to more detail on the pros and cons of this LED lighting later in the post. 

DIY cabinet lighting materials

When I bought these years ago, they only came in one « temperature » that was a bit cooler than I preferred (but still looked great!). Now this brand offers many colors and temperature options to pick from. 

Here they are lit up: 

I had an outlet installed (connected to a switch) before we finished up the drywall in the kitchen. It’s on a wall at the end of the upper cabinets, and I had it placed low so it’s hard to see: 

You do not have to have a dedicated outlet, it just makes the lighting less intrusive to the overall kitchen design and makes it easy to operate from a switch. 

This project can also be completed using outlets from behind appliances.

Cabinet lighting installation 

For the lower lights I ran the cord and cover up inside the cabinet on the left inside. For the uppers I ran the cover down the left side of the cabinet, behind the trim: 

You only see it if you look for it. There’s a slight bump where the adapter and lights connect but other than that it’s seamless. If someone ever notices it you know what I give them — a cookie. 🙂 

The strips have a sticky back — so peel the paper off and just stick it to your surface. Mine stuck fine to painted and unfinished trim. 

For the uppers I ran it along the back of the header. I drilled holes between each set of cabinets and threaded it through: 

When you get to the end of where you need the lights, cut them. Make sure to do this where the little scissor marks are and make sure they are not plugged in!:

So if you have a spot where you want the lights, then a break, then you want them again, this is your solution, but only using one 16-foot length section of lighting (per the manufacturer). 

I bought the iron because I thought I’d have a break in the cabinet over our fridge. I pulled the light through in the back of the cabinet (where it met up with the other cabinets that are further back) and needed to get that light to the front of that cabinet (to attach the lights to the back of the header). To do so meant running it along the sides, which you would see. 

Instead of trying to connect the strips, I came up with a simpler solution. 

I went ahead and ran the lights along the sides of that cabinet, and then picked up some tiny crown molding (found mine at Home Depot): 

Then I installed it a little low so you can see the glow of the lights coming out of the top:

Remember these are LED lights so they stay very cool to the touch. 

This is a lighting trick you can use with regular crown molding too! It’s a cool look, especially in a basement or theater room. It offers low ambient light in a room that you want mostly dark. Just make sure not to have your crown go all the way to the ceiling. 

If I had connected wire I would have had to hide that running along the sides anyway, so this was an easier solution. 

Upper and lower cabinet lighting result

I just love, LOVE warm accent lighting, especially in a kitchen!:

This really shows the true look of them when they are on. This was during the day and they look warmer here. They are LOVELY! I love the low light at night. 

These are easy to install on one bank of cabinets like we have here. They’d also work great in a bookcase or built ins. 

Once you’ve had under cabinet lights it’s hard to go without them!

These lights are really great for task lighting in a kitchen at night, even with all of the overhead lighting on: 

Pros and cons to this type of LED cabinet lighting: 

If you have any questions about this process please let me know. These are a really affordable and energy efficient way to add accent lighting to your kitchen! 

Here’s an image to pin for later if you are interested: